Makita 2030 Manual Planer Jointer Pdf Viewer
.155' x 1,MOmm l 6 - 1 / 8 ' No. Of knives No load speed 7,000 R/min.
Planer- Jointer 320 mm (1242') MODEL 2030N Max. Cutting depth 0 mm 150 mm 150 mm 240 mm I O ' - 5 - 7 / 8 7 l5-7/8'.BEFORE CONNECTING YOUR TOOL GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar t o KEEP GUARDS IN PLACE and in working order. REMOVE ADJUSTING KEYS AND WRENCHES.RISK OF REDUCE THE in off position before plugging USE RECOMMENDED ACCESSORIES.
Consult the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury t o persons. NEVER STAND ON TOOL. Serious injury could occur or if the cutting tool is accidentally contacted.GROUNDING INSTRUCTIONS ALL GROUNDED, CORD-CONNECTED TOOLS: breakdown, grounding provides a path of least resistance for electric current t o reduce the risk of electric shock. This tool is equipped with an electric cord hav- ing an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accord- ance with all local codes and ordinances.Never stick your finger into the chip chute.
Chute may jam when cutting damp wood. Turn off the planer-jointer and then clean out chips with a stick. 1 4.ADDITIONAL SAFETY RULES FOR AUTO-PLANER 1. Two or more pieces of narrow but similar thickness stock can be passed through the auto-planer side by side. However, allow some spacing between the stock t o permit the feed rollers t o grip the thinnest piece.HOW TO USE AUTO-PLANER Adjusting depth of cut The maximum depth of cut changes in terms of the cutting speed and the width of the workpiece to be cut. Insert the workpiece flush with the in- feed table top so that the front end of the workpiece reaches 30 mm (3/4 t o 1-1/8') beyond the.Switchover cutting speed Turn the speed change lever to the right for high speed, and to the left for low speed. Change speeds while the tool is running, but do not attempt to do actual planing operation.
Chip deflector The ejecting distance of chips can be adjusted by means of the chip deflector.JOINTER 1. Cutting depth the depth of cut with the depth adjustment knob while watching the graduation on the scale 2. Fence angle (0 45') Set the depth of cut to '0' graduation. Loosen the thumb screws holding the fence in place.
Pull out the fence by at (1') and tighten the thumb least.OPE RATION 1. Auto-Planer Determine the depth of cut and the cutting speed in terms of the width of the work- piece you intend to cut. Insert the workpiece flush with the table top.
When cutting the long and heavy workpiece, lift up the end of the workpiece slightly.Jointing edge Set the fence square with the table. Hold the best face of the workpiece firmly against the fence throughout the feed.
10) CAUTION: Cover the cutterhead with the safety cover when the fence i s pulled out. 1 1 ).Direction of grain Avoid feeding workpiece into the Jointer against the grain shown in Fig.13. The result will be chipped and splintered edges. Feed with the grain as shown in Fig. 14, to obtain smooth surface. Wor kpiece Outfeed table Cutterhead Wrong feed -against the grain.CHANGING PLANER BLADES Removing blades Remove the screw on the outfeed side of the chip cover.
Then open the chip cover. Loosen the hex bolt with the wrench and lift Set the depth of cut for Jointer to maximum graduation.Lock the drum the position shown in socket wrench.
Remove the hex bolts and the drum cover. When removina the blade from the Auto-Planer, lock the drum in Fig. 18 and push the blade the screwdriver.When removing the blade from the.Auto-Planer, press down on both ends of the blades with wooden levelers.On the Jointer, the leveler on the outfeed table and slide blade edge. The edge just contact underside leveler.
Lock the drum the position shown in Fig. Adjusting infeed/outfeed rollers (Auto-planer) NOTE: The planer infeed and outfeed rollers are factory adjusted. If you notice the adjust- ment is off, kindly do Use the wrench to loosen the installation nuts slightly. Turn the adjusting screw to obtain a level of from 0.1 to.Keep the to about brushes clean and free to slip in the holders. Both brushes should be changed the same time. Use only Makita carbon brushes.
Makita 2030 Planer Jointer Craigslist
Remove the screws that hold the chip cover and the switch cover. Set the speed change lever in the neutral position and remove the switch cover.Take out the worn brush, insert the new one and secure the brush holder cap. Cleaning Always brush off dirt, chips and foreign matter adhering to roller surfaces, motor vents.
Make sure that water or oil does not enter the motor. Lubrication (periodic) Oil the chain (after removing the chain cover), the column moving parts (contact.7.5 mm (5/16”). Blades may be used down to 24.5mm (1”) width.
Makita Planer Jointer 2030 Parts
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Surface of the Wing.ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified i n this manual. The use o f any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only i n the proper and intended manner.180-1200 Dressing Stone (Part 741801-4) Leveler (Part No.
Hand Planer
41 1908-71 (Part No. 411447-7) Wrench (Part No. 781202-4).Seo -19-'84 US (12-1/2') PLANER-JOINTER Model 2030N.Note: The switch and other part configurations may differ from country to country.2030N MODEL DESCRIPTION MACHINE Head S r e w M5x12!Wilh Washer Chip Cover Chip Blast Pan Head Screw M 5 x l 2 IWith Washer) Plane Bearing 10 Rod 1 0 - 4 0 0 Pan Head Screw M5x12 IWith Washer.MODEL 2030N ' i t M DESCRIPTION MACHINE Ruler Holder R Hex Flange Head Bolt M8xZO Pan Head Screw M5x16 With Washer) Ruler Bar L F i x Spring Pin 4 - 3 2 Knob 40 Hex Bolt Max25 lWith Washer) Be'. MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory.
It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Copyright © 2019 Makita® U.S.A., Inc. All Rights Reserved - 14930 Northam St., La Mirada, CA 90638, USA (714) 522-8088Trademarks: Makita®, LXT®, AVT® and the Makita® logo, Teal color and Black & White color combination are the registered trademarks of Makita®. The other trademarks, service marks and logos displayed in the Website are registered and unregistered trademarks of Makita® and others. Nothing contained on this Makita® site should be construed as granting, by implication, estoppel, or otherwise, any license or right to use any trademark displayed on this site without the written permission of Makita or such third party that owns the trademark.